In life, we often encounter such troubles: after the tape stuck on the surface of desktop, glass or cup is torn off, it will leave sticky marks that are difficult to remove, which will affect the appearance. After a long time, it will attach a layer of dust, which is also very unsanitary. The following are my personal attempts to solve this problem. 1 nail polish remover is the most effective and always used method. No matter how long the "history" is and how big the offset printing area is, drop some nail polish remover for girls to wash nail polish, soak it for a while, and then wipe it with a paper towel to ensure that the surface of the article is as clean as new. However, there is a problem. Because nail polish remover is very corrosive, it can't be used on the surface of items that are afraid of corrosion, such as painted furniture and laptop shells. Although the offset printing was clean when I first used this method, the paint surface of the laptop shell was badly damaged, and some nail polish remover flowed into the computer inner shell, which was corroded. Therefore, although nail polish remover can remove the traces of adhesive tape, we must pay attention to protect the items with traces from corrosion. Scope of application: offset printing has a long history, large area and is not easy to clean and corrode. 2 Blower Heat the offset printing blower to the maximum heat, blow it on the tape trace for a while, let it soften slowly, and then wipe it off with a hard eraser or a soft rag. Scope of application: it is suitable for articles with relatively small tape traces and long offset printing time, but the articles should have sufficient heat resistance. 3 medical alcohol immersion offset printing Drop some medical alcohol on the trace surface, soak for a while, and then wipe it off with a soft cloth or paper towel. Of course, articles with tape marks must not be afraid of alcohol corrosion. Similarly, if you have expired perfume or astringent water, it can also be used instead of alcohol, because there is a certain amount of alcohol in it (reference: what is the use of expired or unsuitable skin care cosmetics), and these two kinds can be applied to anything, after all, there will not be too much alcohol in it. Scope of application: the surface of articles that are not easily corroded. 4 Eraser Eraser Offset Printing This method was often used when I was a child at school. Rub it with an eraser, and the rubber crumbs can just stick the adhesion marks. Scope of application: used for small areas and new traces, but invalid for large areas of tape traces. 5 computer cleaner erasing offset printing is usually used to wipe the cleaner of camera lens and computer screen, and can also be used to erase tape traces. Scope of application: It is very effective for tape printing with smooth surface. 6 Time-saving and labor-saving "glue remover", also known as "glue remover", is sold in some auto parts stores. Spray a small amount, and it will be wiped off quickly. Scope of application: large offset printing that is difficult to remove, but if you don't often encounter the trouble of tape marks, there is no need to buy a bottle specially, just use the author's little coup.

Excuse me, how to quickly remove the glue left by various tapes?

020202 1, alcohol removal method

020202 Soak a soft cloth with 95% alcohol, and then gently wipe the adhesive, the adhesive will become soft and easy to fall off, and alcohol will generally not damage the surface of plastic parts or car paint. But sometimes it is found that alcohol is not very effective for some viscose. This can be achieved by gently wiping the adhesive with a soft cloth dipped in a little gasoline. At this time, it should be noted that gasoline has a "dissolving" effect on some plastics or paints, so it must be used with caution: either wipe it gently in an unimportant place first and use it if there is no problem; But be careful not to use too much gasoline and use as little as possible. Generally speaking, wiping the body surface with gasoline for a short time has no obvious effect on the paint film on the body surface. In this way, the adhesive can be easily removed. 020202 2. Removal of essential oil

020202 It is more useful to apply some wind oil essence to the left mark. 020202 3, transparent tape sticking method

020202 Stick it with scotch tape, leaving no trace. 020202 4. Removal of adhesive remover

020202 A bottle of glue remover is only more than 20 yuan, which can be used in many places for a long time.

How to remove the adhesive traces left by scotch tape

The method is as follows:

1, you can use an eraser. When you wipe it, you should wipe it bit by bit along the edge, and the effect is also ok. Just because the viscosity is different, the time is different. If you can, use alcohol and an eraser. It works well.

2. It is also effective to soak the cloth in vinegar or water or heat it. Their principle is to soften the traces of scotch tape. When the adhesion is weak, it is much easier to be clear. But no matter which kind, we must let these items completely cover the traces, and wait until the sticky stains are completely soaked before they can be easily and effectively removed. If there is any trace, nail polish remover used by ordinary girls will do.

3. Not only vinegar and water, but also soap with a little mixture of ammonia and turpentine can not only easily remove the traces of transparent tape, but also make the glass surface more shiny, such as some tiles and ceramics.

4. In fact, there are many methods, such as sodium chloride solution, paint thinner, wind oil essence, special cleaner, sports shoes decontamination paste and toilet cleaner.

How to wash away the traces of tape?

Methods of removing traces of adhesive tape:

1, with pen cleaner, which can be bought in art shops. Wipe it with a paper towel dipped in a small amount of pen cleaner, and it will be easily wiped off.

2, with an eraser, suitable for removing small traces of glue marks, but it needs patience. It will turn black at first, and then clean it slowly.

3. Wipe it with a paper towel dipped in alcohol (preferably with industrial alcohol, or without medical alcohol), and then rub it a few times to clean it.

4. Use nail polish remover. Usage is the same as alcohol acetone. The effect is also very good. Nail polish remover doesn't require quality, it's good and ordinary, as long as it can wash off nail polish.

How to get rid of tape printing

Wipe with a cotton ball of acetone or ethyl acetate.

How to remove the sticky marks of adhesive tape

Scrub with nail polish remover and alcohol.

How can I remove the traces of scotch tape?

Here are some ways to help you. ...

1, put face oil on it, wipe it evenly, dig it off with your nails first, and then wipe it off with a wet towel.

2. Blow with a hair dryer and bake the glue to get rid of it.

3. Wipe it with essential balm, and it will fall off after a while. Just try it.

4. You can try the eraser. But at first, you may feel that the more you rub, the dirtier you get. But if you rub it for a long time, you will see the effect. This method is tiring and requires perseverance.

5, soak in water, put a little detergent, and then brush with an old toothbrush.

6. Wipe with a cloth dipped in alcohol or spirit Erguotou.

7. Soap with a little mixture of ammonia and turpentine can remove a lot of dirt and make the glass surface more shiny (this article is suitable for tiles, ceramics, glass, etc. ).

8. Some surfaces can be removed by repeatedly sticking and tearing with transparent adhesive.

9. Wipe it off with a little sodium chloride or paint thinner.

10, wipe with cotton swab dipped in nail polish remover.

1 1. Wipe with special cleaner or sports shoes decontamination paste.

12. If the trace left behind becomes hard after a long time, you can soften it with a hot towel first and try again.

How can there be glue where the tape has been stuck and how to clean it?

Methods of removing adhesion marks of transparent adhesive tape;

Tools: multifunctional adhesive remover, scraper, paper towel.

Because the surface of scotch tape is a film, it can be waterproof. When dripping liquid, you can drop it from the corner first, so that you can enter through the gap.

After about 10 seconds, it can be found that the viscose began to get fat and began to lose its viscosity. In addition, some corners began to tilt. At this time, you can just tear a small corner and then drop it. So that you can fully contact the glue inside.

The liquid will drip again, because the tape needs to drip layer by layer, and it can be operated from top to bottom if possible. This can save more time. Then the whole tape was torn off.

If the glue remains below, you can drip the liquid again and wipe it off with a paper towel. Because of the length of the glue, you can wait about 5 seconds before wiping it.

If some parts of the factory are not clean enough, you can lower it a little and do the final treatment. After wiping off the glue, you can find that the wooden floor is clean without any damage.

Six ingenious ways to get rid of tape traces in stubborn offset printing

1, wind oil essence to remove tape traces.

2. Eraser's method of erasing tape traces

3. Use alcohol to remove offset printing

4, vinegar or white vinegar to remove the glue on the tape.

5. Method of removing glue from adhesive tape with hand cream

6, hair dryer heating offset printing-how to remove the glue left by the tape?

7, nail polish remover to remove tape traces

8. Glue remover-the new nemesis of tape traces

9, computer cleaner erase tape traces

There are many factors to be considered to remove the glue left after the tape is torn off, such as whether the article is easy to corrode, the size of the tape trace, the cost of removing the tape trace and so on.

How to remove the tape marks on the knife

Water it first, then scrape it off with a small blade. Sticker removal trick! Friends who drive have been exposed to stickers, such as many small ornaments in the car, transparent tape for wedding floats, and certificates of some accessories. After these things are removed, they often leave hard-to-remove sticker marks in the car or on the surface of the car body, which cannot be removed or scraped off with hard objects. What do we do? In practice, we find that the following two methods are good: alcohol removal. Dip a soft cloth with 95% alcohol, and then gently wipe the adhesive, the adhesive will become soft and easy to fall off, and alcohol will generally not damage the surface of plastic parts or car paint. But sometimes it is found that alcohol is not very effective for some stickers. This can be achieved by dipping a soft cloth in a little gasoline and gently wiping the sticker. At this time, it should be noted that gasoline has a "dissolving" effect on a certain plastic or paint, so it must be used carefully: either gently wipe it in an unimportant place first and use it if there is no problem; But be careful not to use too much gasoline, as short as possible! I tried to wipe the car body surface with gasoline for a short time, but it had no obvious effect on the paint film on the car body surface. In this way, the adhesive can be easily removed ... a bottle of adhesive remover is only 20 yuan, which can be used in many places. Can be used for a long time. Is there any way to remove the tape stains at the gate? Stick some decorations on the door with super adhesive paper, and then take them off, leaving pieces of sticky marks on the door. You can use gasoline or kerosene to wipe off the adhesive tape, or you can buy 1200 water sandpaper to wipe off the spots, and then buy a can of transparent varnish and dilute it with banana oil, so that the brightness can be restored after one brush. Don't brush nail polish. Although the glue stain can be removed, it is a pity that the door will become a white stain. Tape: first scrape off the tape with a knife, and then wipe it with petroleum essence; Scrape off the adhesive tape with frosted glass and wipe it with turpentine. There will always be some labels on the newly bought stainless steel pot or glassware by the method of removing self-adhesive trademarks. After the label is torn off, it is difficult to remove the traces left by the adhesive on it. Wipe with a wet cloth and scrape with a knife, which often leaves traces. After many times of practice, I summed up some tips to share with you. For the self-adhesive marks on the surface of hard objects, we can apply grease-free nail polish remover on the surface of the object, and then gently wipe it with a soft cloth; These traces can also be removed with industrial alcohol or gasoline. If these stickers stick to your skin, you can also remove them with lemon juice. In addition, hand cream can also achieve the effect of removing adhesive. Hand cream contains a lot of water (generally above 70%) and a certain amount of surfactant. Surfactant has good wetting, penetrating and dissolving ability, and can quickly penetrate between the adhesive and the surface of the object, thus achieving the purpose of cleaning. You can also find some similar products, such as face cream, facial cleanser and detergent, which have the same effect. For the stubborn adhesive on the carpet, the best way is to carefully trim the adhesive traces on the top of the carpet fluff.